• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Dodge, Jeep and RAM Forum dedicated to FCA owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the SRT Forum today!


UOA - Oil Analysis sampling methods COMPARED

OP
BULL

BULL

Oh NO! Not that guy!
Staff Team
Founding Member
U.S. Marine Veteran
Donating Member
HFCOTM
Wiki Contributor
Member ID
#1079
Messages
14,585
Reactions
44,737
Likes
402
City
Weld County
State
CO
Country
United States
Vehicle
MY16 M6 Challenger Hellcat
HFCOTM
View Images
Thread Starter #21
I never drain the oil when it's hot. Don't have to worry about getting burned as a result.😉
Blackstone still gives me good results.
Heck, we have 0W cold oil. Why would it have to be hot when you drain it?

The same reason I let it drip for hours after I pull the plug out, the lower the viscosity, the more that will come out.
 


Whatknot

2000 Posts Club
Member ID
#6510
Messages
2,120
Reactions
10,508
Likes
252
City
nearest is Portland, but live in the country
State
OR
Country
United States
#22
I never drain the oil when it's hot. Don't have to worry about getting burned as a result.😉
Blackstone still gives me good results.
Heck, we have 0W cold oil. Why would it have to be hot when you drain it?

Interesting theory, it aligns with my own.
If my car sat just sat for a day, two, three, seven, or whatever, everything that is goingto drain down to the oil pan, has.
So then i drain it.
Then i pour in a quart of clean oil with the plug still out, and let it flush out even more.
Then i usually go do something else for a while, after removing the filter, and leave the plug out.
Let it drip for a half hour, or hour.
Then come back, install new filter, plug, and refillwith oil.

Why start it up, got for a little drive, then change it. You have pumped all that oil back throughout the entire engine, that just spent a day, or days draining to the pan.
Always seemed illogical to me, unless i was going to let it sit there again with the plug out for days.
 


TrackDay

Active Member
Founding Member
Member ID
#1012
Messages
467
Reactions
808
Likes
117
City
Great White North
State
MN
Country
United States
Vehicle
2016 Dodge Challenger
#23
The same reason I let it drip for hours after I pull the plug out, the lower the viscosity, the more that will come out.
Yeh, I let it drip for a few minutes. When I don't see a steady drip every few seconds it's fine to plug it back up. But I change my oil about every 3k miles so there's lots of cushion there.
 


OP
BULL

BULL

Oh NO! Not that guy!
Staff Team
Founding Member
U.S. Marine Veteran
Donating Member
HFCOTM
Wiki Contributor
Member ID
#1079
Messages
14,585
Reactions
44,737
Likes
402
City
Weld County
State
CO
Country
United States
Vehicle
MY16 M6 Challenger Hellcat
HFCOTM
View Images
Thread Starter #24
Yeh, I let it drip for a few minutes. When I don't see a steady drip every few seconds it's fine to plug it back up. But I change my oil about every 3k miles so there's lots of cushion there.

You saw the mileage on my oil changes in the reports?

o_O
 


TrackDay

Active Member
Founding Member
Member ID
#1012
Messages
467
Reactions
808
Likes
117
City
Great White North
State
MN
Country
United States
Vehicle
2016 Dodge Challenger
#25
You saw the mileage on my oil changes in the reports?

o_O
I did not originally. I do now. So, at this point let's just all acknowledge you're a little obsessive.
 


OP
BULL

BULL

Oh NO! Not that guy!
Staff Team
Founding Member
U.S. Marine Veteran
Donating Member
HFCOTM
Wiki Contributor
Member ID
#1079
Messages
14,585
Reactions
44,737
Likes
402
City
Weld County
State
CO
Country
United States
Vehicle
MY16 M6 Challenger Hellcat
HFCOTM
View Images
Thread Starter #26
I did not originally. I do now. So, at this point let's just all acknowledge you're a little obsessive.

I was proud of myself for going a full year with this last change instead of the 6 months that I was thinking...

:unsure:
 


TrackDay

Active Member
Founding Member
Member ID
#1012
Messages
467
Reactions
808
Likes
117
City
Great White North
State
MN
Country
United States
Vehicle
2016 Dodge Challenger
#27
I was proud of myself for going a full year with this last change instead of the 6 months that I was thinking...

:unsure:
Baby steps . . .
 


Speedy!

Infomercial Producer
Staff Team
Founding Member
U.S. Marine Veteran
9 Second Best E/T
HFCOTM & HFCOTY
Member ID
#1070
Messages
6,068
Reactions
15,532
Likes
402
City
Murfreesboro
State
TN
Country
United States
Vehicle
2016 Hellcat Go Man Go
#28
Great info @BULL as I've wondered about this very thing. I don't sample every oil change but I do occasionally just to see how things look. I'm going to do some checking here soon now that I've been running E85 for a while as people say you're supposed to change the oil more frequently, but I'm a skeptic about that ;) As you say, test :)

As for changing the oil when hot vs cold, it probably doesn't make any difference if you're just changing the oil, although I've always done it hot. If you're having the oil sampled the thought is that more of whatever may have been in the oil would be suspended and a better representation in the sample analyzed, but looking at Bull's results I'd question that now.

P.S. Bull, you need to enjoy that car more life's short! :)
 


OP
BULL

BULL

Oh NO! Not that guy!
Staff Team
Founding Member
U.S. Marine Veteran
Donating Member
HFCOTM
Wiki Contributor
Member ID
#1079
Messages
14,585
Reactions
44,737
Likes
402
City
Weld County
State
CO
Country
United States
Vehicle
MY16 M6 Challenger Hellcat
HFCOTM
View Images
Thread Starter #29
Thanks guys, I'm working on my "issues", but it's a battle... : )

And yes, I do need to get out in the car more... : (

I had every intention of getting out to HPR a couple of times this year and it just didn't happen. :mad:



Also, for those that get the vacuum pump, you can't get the 1/4" tube all the way down the 6.2L dipstick hole. There is a reduction in diameter at the bottom of the dipstick tube that prevents the 1/4" tube from making it into the oil in the pan.

What I did was get some tube that fit the I.D. of the 1/4" tube, which was a tight fit, and used a two piece arrangement. You need the 1/4" tube up at the top to seal against the vacuum pump. (You might be able to get the vacuum pump seal to squish down on the smaller tube, but I didn't want to try.)

The tube I got from McMaster:
McMaster 8359K13

Replacement 1/4" tube from Amazon:
1/4" (or 6mm) O.D. tube

So you end up with the smaller tube in the dipstick tube, and a stretch/friction fit between the two tube sizes just above the dipstick tube, and then the 1/4" tube in the vacuum pump.

I'm not planning on reusing the tube as I don't want the oil left in the tube to contaminate the next sample.
 


McLovin

Active Member
Founding Member
Member ID
#1024
Messages
469
Reactions
1,468
Likes
117
City
Syracuse
State
NY
Country
United States
Vehicle
2015 Challenger Hellcat
#30
Was thinking about this while trying to get to sleep last night.

I wonder what the process is at the lab once they receive the sample? I mean, you go thru all this trouble to get a consistent and most accurate sample... but I wonder if they just pour what they need for the analysis from the top of the bottle run that?

(and yes...I need another hobby)
 


OP
BULL

BULL

Oh NO! Not that guy!
Staff Team
Founding Member
U.S. Marine Veteran
Donating Member
HFCOTM
Wiki Contributor
Member ID
#1079
Messages
14,585
Reactions
44,737
Likes
402
City
Weld County
State
CO
Country
United States
Vehicle
MY16 M6 Challenger Hellcat
HFCOTM
View Images
Thread Starter #31
Was thinking about this while trying to get to sleep last night.

I wonder what the process is at the lab once they receive the sample? I mean, you go thru all this trouble to get a consistent and most accurate sample... but I wonder if they just pour what they need for the analysis from the top of the bottle run that?

So some of the numbers above vary by small percentages, but for example, the viscosity and TBN seems like there is more than a small variance.

However I also saw in another report for an unknown person where Blackstone stated that the TBN was not a linear scale... :unsure::unsure::unsure:
 


jonx96

4000 Posts Club
8 Second Best E/T
HFCOTM
Member ID
#4957
Messages
4,246
Reactions
10,573
Likes
302
City
Small town
State
MI
Country
United States
Vehicle
2019 Challenger Redeye
#32
Great info @BULL as I've wondered about this very thing. I don't sample every oil change but I do occasionally just to see how things look. I'm going to do some checking here soon now that I've been running E85 for a while as people say you're supposed to change the oil more frequently, but I'm a skeptic about that ;) As you say, test :)

As for changing the oil when hot vs cold, it probably doesn't make any difference if you're just changing the oil, although I've always done it hot. If you're having the oil sampled the thought is that more of whatever may have been in the oil would be suspended and a better representation in the sample analyzed, but looking at Bull's results I'd question that now.

P.S. Bull, you need to enjoy that car more life's short! :)
Did you ever get your results back?
 


Speedy!

Infomercial Producer
Staff Team
Founding Member
U.S. Marine Veteran
9 Second Best E/T
HFCOTM & HFCOTY
Member ID
#1070
Messages
6,068
Reactions
15,532
Likes
402
City
Murfreesboro
State
TN
Country
United States
Vehicle
2016 Hellcat Go Man Go
#33
Stay tooned :cool:
 


OP
BULL

BULL

Oh NO! Not that guy!
Staff Team
Founding Member
U.S. Marine Veteran
Donating Member
HFCOTM
Wiki Contributor
Member ID
#1079
Messages
14,585
Reactions
44,737
Likes
402
City
Weld County
State
CO
Country
United States
Vehicle
MY16 M6 Challenger Hellcat
HFCOTM
View Images
Thread Starter #34

Speedy!

Infomercial Producer
Staff Team
Founding Member
U.S. Marine Veteran
9 Second Best E/T
HFCOTM & HFCOTY
Member ID
#1070
Messages
6,068
Reactions
15,532
Likes
402
City
Murfreesboro
State
TN
Country
United States
Vehicle
2016 Hellcat Go Man Go
#35
LOL, no I've taken a bit of a break but have some content I just haven't put together yet.
 




Top